Mechanical Engineering Test
__________ is the angle made by the face of the tool and the parallel plane to the base of the cutting tool.
___________ is an opening through the cope.
___________ is that type of motion in which there is reduction in amplitude over every cycle of vibration.
_____________ is the operation of enlarging a previously drilled hole.
_______________ is a beam having its end portion extended beyond the support.
A couple of two bodies produces which type of motion?
A jig is a device which is used to:
A process in which gas is heated such that the product of its pressure and volume remains constant is known as _______.
A solar collector receiving solar radiation at the rate of 0.6 kW/m2 transforms it into the internal energy of a fluid at an overall efficiency of 50%. The fluid heated to 350 K is used to run a he...
According to the Boyle's law:
Calculate the angular velocity of a body whose rotations per minute is 60.
Calculate the centrifugal force for a body moving in a circular path, given that the mass of the body is 10 kilogram, its angular velocity is 10 radians per second and the radius of the circular pa...
Calculate the circular pitch of a gear whose pitch circle diameter is 12.74 millimeters and the number of teeths on gear wheel are 20.
Calculate the coefficient of friction of a body whose limiting friction is 10 newtons and the value of the normal reaction is 5.
Calculate the coefficient of friction of a body whose limiting friction of which is 10 newtons and the value of the normal reaction is 5.
Calculate the economic order quantity of a plant in which the total raw material utilized per year is 1600 tonnes, procurement cost per order is $1000 and the annual inventory carrying cost per ite...
Calculate the frictional power of an engine if the indicated power is 10 watts and the brake power is 5 watts.
Calculate the mechanical efficiency of an engine whose brake power is 20 watts and indicated power is 40 watts.
Calculate the moment of a 20 newtons force at 10 meters perpendicular distance from the point about which the moment is required.
Calculate the number of joints in a chain if the number of links is 5.
Calculate the specific heat of a gas at constant volume, given that the mass of the gas is 100 kilograms, the initial temperature of the gas is 20 kelvins and the final temperature of the gas is 50...
Calculate the strain in a material whose original length before undergoing strain is 10 centimeters and the length after undergoing strain is 100 centimeters.
Calculate the torque for a solid shaft having a radius of 10 millimeters and torsional shear stress of 112 newtons per square millimeter.
Calculate the value of crippling load of a specimen, given that the crushing stress is 160 newtons per square meter, cross sectional area is 80 square millimeters, Rankine's constant is 1, length o...
Due to which of the following properties does molding sand adhere to the sides of the molding box?
How many revolutions of crankshaft does it take to complete one working cycle in a four stroke engine?
If L is the length of the journal and d is the diameter of the journal then, in a square bearing:
If M - bending moment, I - moment of inertia, E - young's modulus of elasticity and R - radius of curvature then, which of the following is the correct bending equation for a beam?
If Q is energy, W is external work done and E is internal energy then, According to the first law of thermodynamics, energy Q is equal to:
If the motion between a pair takes place in more than one direction, then this kind of motion is termed as ___________.
If we have to choose a grinding wheel having the least hardness, which grade of grinding wheel should be chosen?
In a programmed evaluation and review technique, if the slack of an activity is negative, then what can be stated for the project completion?
In a simple harmonic motion, number of cycles produced per second is known as:
In involute gears the pressure angle __________ as the gear engages or disengages.
In which among the following wage incentive plans is the worker paid according to the number of units of work produced by him?
In which type of welding is a mixture of Iron oxide and Aluminum used?
In which, among the following engine strokes, is the firing of the vaporized fuel carried out?
In which, among the following governing methods, is a control valve fitted in the fuel delivery pipe in order to control the quantity of fuel mixed in the charge?
In which, among the following scavenging methods, are the inlet and the outlet ports situated on the same side of the engine cylinder?
In which, among the following systems, does no heat or work cross its boundary?
The ability of a material to embed small particles of dust, grit etc. is known as ___________.
The allowance provided on patterns which are used for castings in which contraction is not uniform is known as _________.
The bolt and nut is an example of a:
The broaching operation in which the workpiece moves across the stationary tool is known as _______.
The compression ratio of a diesel engine is:
The forces which meet at one point but whose lines of action lie on different points are known as ______________.
The milling operation of producing surfaces of irregular shape is known as:
The petrol engine works on ___________.
The process of heating the metal to the plastic state followed by application of pressure to form the molten metal into desired shape is known as ________.
The process to improve the fatigue resistance in metals by producing compressive stresses in its surface is known as ________.
The radius of a shaft is 5 millimeters. The shear stress on that shaft is 50 newtons per square millimeter and the polar moment of inertia is 10 (millimeters)4. Calculate the twisting moment on tha...
The resultant of two forces A and B is Q. If A is doubled and the new resultant is perpendicular to A, then:
The shortest time in which an activity can be completed is known as:
The smallest circle drawn to the cam profile is known as ________.
The work measurement technique is concerned with:
Two springs having stiffness 5 and 10 respectively are connected in series. Calculate the combined stiffness of the two springs.
Up to which point in a stress-strain curve is Hooke's law applicable?
What effect does the grain size of a cutting tool have on the tool life?
What is the significance of the above given symbol in work study technique?
What is the value of entropy of a substance at absolute zero temperature?
What is the value of the point angle of a twist drill?
What is the value of universal gas constant in SI units?
What type of gear is used to transmit power at constant velocity ratio between two shafts the axes of which intersect at an angle?
Which among the following is a spring controlled governor?
Which among the following is also known as croning process in which cast parts are produced with dimensional tolerances as low as ±0.2 millimeters.
Which among the following is not a characteristic of rolling contact bearing?
Which among the following is the correct range of value for the included angle of a V-belt?
Which among the following plant layout is known as 'functional layout' or 'analytical layout'?
Which among the following types of chips is usually produced during the machining of brittle materials?
Which branch of engineering mechanics deals with the force which acts upon bodies at rest?
Which of the following devices is used for atomizing and vaporizing the fuel before mixing it with air in varying proportions?
Which technique among the following is known as 'time phase of loading'.
Which type of organization among the following has a straight flow of authority within a single unit?
Which type of sand is used on the face of the pattern before molding?
Which type of thread is used in bench vices in manufacturing units?
Which type of welding is obtained if there is an excess of acetylene?
Within which angular range is the shear stress maximum if a body is subjected to tensile stress in one plane?